Modeling Notes for the Gadget Hamper

From Bloominglabs
Revision as of 01:05, 5 June 2019 by Dosman (Talk | contribs)

Jump to: navigation, search

Contents

Getting the latest version of the Gadget Hamper models

I push my models to GitHub: https://github.com/dosman33/Gadget-Hamper

If folks make improvements to the system please share them. For the moment I'm not intending to include the individual device cradles (except for the universal cradle) in the main repo, those should be separate. However I am happy to link to or reference any new device cradles that are published.

Main page for the Gadget Hamper

Considerations for those designing their own battery packs

  • Keep the charging tabs in your battery pack near the bottom of the battery case so that the cradle can make contact with them. The cradle “top side” can be extended to be as deep as your design needs, but the shallower you can make the cradle the less print material is needed.
  • Watch out for belt clips, especially on short radios. Both how far down it reaches and how far “back” into the cradle it needs to have clearance.
  • Also on short radios, watch for clearance for any buttons on the front side.
Cradle has clearance for the belt clip
Cradle has clearance for front-facing buttons
  • Use the rear deck of the Gadget Hamper to mount indicator LED’s and other components. If space allows you can get away with mounting these on the front of the cradle too.
  • If possible, recess your contact points on the battery. This way a metal object laying across the contacts is less likely to short it out.
  • Avoid excess friction inside the cradle, you want the most minimal contact with the battery/device as you can get away with. Otherwise removing the device from the cradle becomes a two-handed operation. Here are two ways to achieve this:
    • Consider adding what I call "retaining channels" to the sides of your battery pack. This helps to hold your device exactly in place with the charging contacts. Note the ribs that extend into the sides of the battery pack:
    • Even if retaining channels are not used in the battery pack, ribs can be used to provide minimal contact with the device to force it into place. Again, this keeps friction to a minimum.
Retaining channel
Retaining channel meets a rib in a charging cradle. Note that a pair of these ribs is all that holds the radio in place in the cradle.
  • Battery contacts made of stripped wire are simple and work well. Metal coil springs are expensive. There’s nothing wrong with using springs if you have them, but usually a design can be made to eliminate metal coil springs. Taking advantage of the flexibility of the print material can overcome a lot the need for metal springs. See the following photos for examples.
    • Note that 18650 cells can vary in length from 65mm to around 70mm if the cell has a protection circuit included. Five millimeters of variance is a lot to overcome, if you wish to guarantee support for any 18650 cell coil springs may be the only solution. However if you can ensure a consistent brand and make of 18650 cell is used then you can simplify your model and keep the cost to reproduce as low as possible.
Ni-chrome battery tab with a piece of wire insulation behind it used as a spring
Stripped wire used as battery contact
Wire contacts inside a battery holder for an 18650 cell
Stripped wire used for contacts

To embed the Li-Ion charge controller in the battery or leave it in the charging cradle?

The Gadget Hamper gives you freedom to use it however you want. A lot of commercial designs will embed the charge controller in the battery pack (but not all). If you do this it *usually* means that only two contacts are needed to recharge the battery (assuming it has more than one 18650 or other cells, and assuming no temp sensors or other interfaces are involved). This is a little more expensive, but multi-18650 cell charge controllers have come way down in price. Doing it this way also means you can embed a barrel jack in the battery for easy on-the-go charging too.

Moving the charge controller into the charging base means you will need “cell N-1” wiring contacts for multi-18650 cell battery packs. The charge controller needs a leg to each battery junction point, so a battery pack with two 18650 cells will require three contacts from the pack to the charging cradle.

My recommendation: if you are building one or two one-off Li-Ion battery packs, put the charge controller in the battery. It will make life easier in the long run. However, if you are building a fleet of battery packs, it’s worth considering putting the charge controller in the charging base instead. If you have the funds, it’s still worth considering the first option though.


Wiring it up

Obviously wire and electronics are needed to make the Gadget Hamper a functional charger. Here are some resources if you need inspiration.

Contact hardware

Battery tabs are the cheapest option and can be formed into many shapes. Usually I find that I can engineer a solution much cheaper than resorting to a coil spring which is the most expensive solution. However it's always nice to know that these options exist when you need them. Digikey has a wide variety of contact hardware, if you get stuck spend some time searching there.

Charging Boards

Obviously there are boards that support many variety of battery cells. And of course, you can also build the Gadget Hamper to charge NiCD and NiMH batteries too.

Battery internal wiring

Firstly, I assume most folks will be interested in Li-Ion charging. You will need the right kind of charge controller for the right kind of battery pack.


Good in-depth reviews on Lithium battery charging

This info is not required for building your own charging equipment if you are using off-the-shelf boards. However it's always good to understand what is really going on, especially with Lithium batteries. They contain a substantial amount of energy and understanding why it's important to not mis-handle them is worth while.

Personal tools