Difference between revisions of "Restoration of Parks 95 12" surface planer"

From Bloominglabs
Jump to: navigation, search
("Before" Photos)
(Restoration resources)
 
(7 intermediate revisions by one user not shown)
Line 2: Line 2:
  
 
It's not yet been decided whether this tool will get a top-to-bottom overhaul or just be touched up for usability.  This page will be used to track resources with repair information, and to document the process of cleaning it up.
 
It's not yet been decided whether this tool will get a top-to-bottom overhaul or just be touched up for usability.  This page will be used to track resources with repair information, and to document the process of cleaning it up.
 +
 +
 +
== Photos ==
 +
'''Before restoration'''
 +
<gallery>
 +
Image:IMG 20160316 191012263.jpg|On arrival
 +
Image:IMG 20160316 205005456.jpg|Gearbox
 +
Image:IMG 20160316 205013924.jpg|The bed
 +
</gallery>
 +
 +
 +
== Usability ==
 +
The planer is somewhat operational now.  However the pickup roller (infeed roller) is not successfully pulling boards through the cutter.  The fifth link below is for a thread where a similar problem with an identical planer is being discussed, and there are several suggestions we can try there without a full teardown.  Anybody is welcome to attempt work on this, if you'd like a working planer or you're just bored.  Things we can try (but haven't yet) include:
 +
* Confirm that the bed rollers are positioned high enough to support the board rather than having it rest entirely on the bed itself
 +
* Attempt to lower the position of the infeed roller itself - this would be a delicate process, since it's important that the roller height is not lower than the cutting height
 +
* Further clean the bed - using steel wool, then sandpaper up to 1000 grit
 +
* Once clean, apply a layer of non-silicone wax to the bed
 +
 +
 +
== Planned improvements ==
 +
* Build a replacement stand
 +
* Install a hinged motor mount for belt tensioning
 +
* Add a belt guard
 +
* Add a starter switch
 +
* Machine a replacement pickup roller on the lathe / mill
  
  
Line 15: Line 40:
 
[https://forum.canadianwoodworking.com/forum/tools/power-tools/48261-parks-planer Thread on pickup roller performace]
 
[https://forum.canadianwoodworking.com/forum/tools/power-tools/48261-parks-planer Thread on pickup roller performace]
  
 
+
[http://www.dcmorrison.com/ DC Morrison - last known parts supplier]
 
+
== "Before" Photos ==
+
<gallery>
+
[[File:IMG 20160316 191012263.jpg]]
+
</gallery>
+

Latest revision as of 23:18, 3 April 2016

Jesse brought in a Parks 95 12" surface planer, on 03/16/2016. This is a ~280 lb machine, probably manufactured in the 30s or 40s (we'll know more if we can clean up the plate with the serial #). It is cosmetically in bad shape, and has one small operating problem that should be resolvable.

It's not yet been decided whether this tool will get a top-to-bottom overhaul or just be touched up for usability. This page will be used to track resources with repair information, and to document the process of cleaning it up.


Contents

[edit] Photos

Before restoration


[edit] Usability

The planer is somewhat operational now. However the pickup roller (infeed roller) is not successfully pulling boards through the cutter. The fifth link below is for a thread where a similar problem with an identical planer is being discussed, and there are several suggestions we can try there without a full teardown. Anybody is welcome to attempt work on this, if you'd like a working planer or you're just bored. Things we can try (but haven't yet) include:

  • Confirm that the bed rollers are positioned high enough to support the board rather than having it rest entirely on the bed itself
  • Attempt to lower the position of the infeed roller itself - this would be a delicate process, since it's important that the roller height is not lower than the cutting height
  • Further clean the bed - using steel wool, then sandpaper up to 1000 grit
  • Once clean, apply a layer of non-silicone wax to the bed


[edit] Planned improvements

  • Build a replacement stand
  • Install a hinged motor mount for belt tensioning
  • Add a belt guard
  • Add a starter switch
  • Machine a replacement pickup roller on the lathe / mill


[edit] Restoration resources

Restoration worklog @ vintage machinery

Restoration worklog @ estrategy

Owner's manual

Parts list with photos

Thread on pickup roller performace

DC Morrison - last known parts supplier

Personal tools