Essential information about operating our LASER cutter and engraver.
Don't cut anything particularly flammable or noxious. Absolutely NO chlorinated plastics (PVC). Check the Laser Infobase page for the complete list
When using the laser, whether for engraving or cutting, stay and watch your job.
Know where the fire extinguisher is and be ready to use it.
If your job catches on fire:
- You are more important than the laser--do not put yourself in unnecessary danger to save the laser. (Cf. Bloominglabs rules)
- Use your judgment--flare-ups will happen, and most go out quickly (a second or so) on their own.
- Any flame lasting longer than a second or two is a fire--put it out.
Do not look directly into either the cutting laser or even the visible targeting laser.
Make sure the lid is down before you even try starting your job. There is an integrated safety lock-out, but don't rely on this.
The lid should absorb most laser radiation, but if you're cutting reflective material, it wouldn't hurt to use the tinted safety glasses (should be located near the laser).
About our system
We've got a: 5th Generation Hobby Laser from Full Spectrum
Always make sure the water pump is working and that there's plenty of water in the reservoir (blue bucket below the blower and compressor). Operating the laser without the cooling system running will damage it.
- Make sure print area is clear and visible surfaces are clean (if you can, take a look at the lens, checking for residue/particulates)
- If anything needs cleaning, please do so before printing--it'll make your print easier and potentially more accurate
- Turn on main power strip
- Verify water pump is pumping water (you should be able to feel the flow in either hose)
- Verify ventilation fan, and air assist compressor are running
- Start/attach dedicated computer and start up RetinaEngrave
- Home lens head by using home button on device or pressing 'H' in RetinaEngrave
- Place material to be cut/etched on honeycomb and focus lens
- Close lid, holding it at the middle so it doesn't catch in the back
- Move lens head to top left of desired print area using either onboard or RetinaEngrave controls
- Adjust speed and power to appropriate levels for material and job
- Run raster portion before vector
- Watch your job like a hawk
- Allow the blower to clear any remaining smoke before opening the lid
- Remove your engraved/cut object!
- For higher precision placement of the lens (say, for engraving on small objects) hit the padlock button on the control panel until it says "Unlocked", then use your hands to carefully move the lens to the correct starting location. There's no need to relock the lens position when you are done, just start the operation.
(Read The Frickin' Laser Manual)
Lenses and Focusing
Make sure never to touch lenses directly--oils will shorten their lifespans. When handling lenses, make sure you wear gloves and/or use only oil-free tools to touch them.
- 2" (for cutting and engraving up to 1/4" thick)
- The unmarked aluminum billet stored under the laser is used for focusing this lens.
- 1.5" (for extra fine engraving eg for fonts < 8 points)
- 2.5" (for thicker cutting eg over 1/4" and straighter cuts)
- 5" (for increased working distance eg engraving bowls)
FocusingPer the manual:
To focus for engraving or cutting, simply place the billet on the top of the engraving plane and then release the locking mechanism on the focus head until the air assist nozzle rests on top of the billet. Then re-tighten the sliding head and remove the billet from the work piece.
We will probably be making additional focal billets for the other lenses. Until then, they may still be used fairly easily by measuring the distance of their focal length to either the surface (for engraving) or half the thickness (for cutting) of your material.
The laser cutter needs regular cleaning: both optics and housing need to be kept clean for optimal performance and longevity.
The amount of smoke and residue items produce seem to be good indicators of how much you'll have to clean after a given job.
Optical elements (mirrors and lenses) should be cleaned with camera-quality optical wipes, papers, or cotton swabs and lens fluid or isopropyl alcohol. As stated above: Make sure never to touch lenses directly--oils will shorten their lifespans. When handling lenses, make sure you wear gloves and/or use only oil-free tools to touch them.
The honeycomb support grid may be cleaned with hot water and dish soap--soak it in the sink. Other users have noted that Simple Green works well as a cleaning agent.
The floor can be cleaned the same as the grid (minus the soaking, of course).
Check the Laser Infobase page for an ever-growing list of materials and settings.
As you cut and engrave materials with the laser, please record the settings you had success with there.
Prints, whether cuts or engraves, go through Full Spectrum's RetinaEngrave virtual print driver and motion control interpreter. Anything that will print in Windows should be able to print to this.
Inkscape is a free, cross-platform, open source vector graphics tool that works well for setting up vector cuts.
GIMP is a free, cross-platform, open source raster graphics tool that works well for editing images to be engraved.
Per Full Spectrum:
Just remove all the small button head screws that hold down the silver aluminum bottom. Don't remove the big black screws that hold down the corner brackets. Avoid stripping screws when removing them. Reinstall the screws by pushing the installed t-nuts using a paper clip through the slots cut in the bottom. Both reinstalling and removing is much easier if you flip it upside down to see what you are doing.
From another user:
Another tip: if your object is flat (say a 2ft x 2ft piece of acrylic) you will need to remove the rubber feet to get the laser low enough to cut/engrave. Those are held in with M5 cap screws (4mm hex key). Again, do not remove the 4 cap screws that hold the plates onto the framing.