Difference between revisions of "PrintrBot Simple"
From Bloominglabs
m |
(Added link to 3D Printers page) |
||
| (5 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
| − | [ | + | [[Image:PrintrBot.jpg|200px|thumb|PrintrBot its cabinet]] |
| − | + | Bloominglabs has a PrintrBot Simple v1 (1310) [[3D Printers|3D printer]], controlled with a [[Sunverge | donated ag150]]. | |
| − | + | == Official Documentation == | |
| − | + | PrintrBot model 1310 is pretty old, and the information on it is not easily available on printrbot.com. All of the official documentation on the "legacy" printrbots can be found in [https://drive.google.com/open?id=0B9oj0J-4qhdjWThtZmY2YzJIRE0 this google drive folder]. The (copyrighted) assembly manual can be found [https://drive.google.com/open?id=0B9oj0J-4qhdjVXZhU3l6Um5LVTg here]. | |
| − | + | ||
| − | + | == Using Locally == | |
| − | + | Login to the ag150 with username "blabs". | |
| − | + | [https://ultimaker.com/en/products/cura-software Cura] software GPL AFFERO V1 | |
| − | + | ||
| + | == Using via Command Line == | ||
| + | Login remotely with secure shell: "ssh -XC blabs@192.168.1.137". | ||
| + | The Arduino terminal can be used to directly talk to the PrintrBot. | ||
Serial is set up to be 115200 baud. | Serial is set up to be 115200 baud. | ||
| − | + | === Useful [http://reprap.org/wiki/G-code g-codes] === | |
| − | Useful [http://reprap.org/wiki/G-code g-codes] | + | * <code>M115</code> reports Firmware installed. |
| − | + | ||
| − | + | ||
| − | M115 | + | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | FIRMWARE_NAME: Marlin v1; Sprinter/grbl mashup for gen6 | |
| + | FIRMWARE_URL:http://www.mendel-parts.com | ||
| + | PROTOCOL_VERSION:1.0 | ||
| + | MACHINE_TYPE Mendel | ||
| + | EXTRUDER_COUNT:3 | ||
| − | + | * <code>M114</code> reports position. | |
| − | + | * <code>M119</code> reports endpoint status. | |
| − | + | ||
| − | [[Category: | + | [[Category:Tools]] [[Category:3D Printers]] |
Latest revision as of 01:45, 14 July 2017
Bloominglabs has a PrintrBot Simple v1 (1310) 3D printer, controlled with a donated ag150.
Contents |
[edit] Official Documentation
PrintrBot model 1310 is pretty old, and the information on it is not easily available on printrbot.com. All of the official documentation on the "legacy" printrbots can be found in this google drive folder. The (copyrighted) assembly manual can be found here.
[edit] Using Locally
Login to the ag150 with username "blabs". Cura software GPL AFFERO V1
[edit] Using via Command Line
Login remotely with secure shell: "ssh -XC blabs@192.168.1.137". The Arduino terminal can be used to directly talk to the PrintrBot. Serial is set up to be 115200 baud.
[edit] Useful g-codes
-
M115reports Firmware installed.
FIRMWARE_NAME: Marlin v1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:http://www.mendel-parts.com PROTOCOL_VERSION:1.0 MACHINE_TYPE Mendel EXTRUDER_COUNT:3
-
M114reports position.
-
M119reports endpoint status.
